桂剥き Katsuramuki

How to get better at katsuramuki

Practise on short pieces first, keep the knife very sharp, and let the vegetable do the turning while the knife makes long, even up-and-down strokes. Go for even thickness before thinness, and change one thing at a time: piece length, then thickness, then vegetable.

The plan below assumes about 15 minutes a day and one daikon every two or three days. Nothing is wasted: the last section lists what to do with the sheets. If you have not seen the cut yet, start with the animated explanation.

Before you start

The knife

A dull edge tears the sheet and makes you push, and pushing is what makes the thickness jump. Sharpen before every practice week. On a single-bevel usuba, keep the flat back flat; a back that has been rounded on the stone will not track evenly. If you are not sure the edge is sharp, slice a sheet of newspaper hanging from your fingers. It should cut without catching.

The daikon

Choose a firm, heavy daikon with tight, smooth skin. A soft or bendy one has lost water and will tear. Cut it into pieces, peel each piece thickly and trim it into an even cylinder. Ten minutes of rounding saves twenty minutes of torn sheets.

An uneven piece has ridges and flat spots where the sheet will tear or thicken. Trim it to a round, even cylinder before starting. As cut Trimmed round ridge flat spot the sheet tears or thickens here even all the way round
Seen from the end. The offcuts go into soup.

Your stance

Stand square to the board with your elbows close to your body. Hold the daikon upright at chest height over the board, not resting on it, so you can see the edge and the sheet can hang down freely.

Seven drills

The drills step up one variable at a time: a short piece at 2 mm, a full piece at 2 mm, then 1 mm, then a whole piece in one sheet, then see-through. 15 cm 210 cm 31 mm 4to the core 5see-through piece length, then thickness (green bar), one change at a time
Drills 1 to 5 on daikon. Drills 6 and 7 move to cucumber and to cutting threads.

1. Short and thick

Piece: 5 cm long. Target: a sheet about 2 mm thick, one full turn without breaking. Work slowly and watch the edge, not the sheet. The aim is the rhythm: knife up and down, daikon turning, edge staying in one place.

Move on when: three pieces in a row give one full unbroken turn.

2. Full width

Piece: 8 to 10 cm. Same 2 mm target. A longer piece means more edge in the cut and more chance for one end to run thicker than the other. Watch both ends of the sheet.

Move on when: the sheet is the same thickness at both ends, checked by feel between finger and thumb.

3. Thinner

Same piece, target 1 mm. Bring the edge closer to the surface and let your right thumb ride on the sheet where it lies over the blade. If the sheet keeps tearing, go back to 2 mm for a day.

Move on when: you can hold the sheet up to a window and see light through it evenly, without dark bands.

The light test. A 1 mm sheet should let you read print through it, evenly, with no dark bands. (Cut with a guide, to show the target.)

4. The whole piece

One sheet from the cylinder down to a core as thick as a finger. Breaks are expected; count them. Fewer breaks per piece is the measure of progress here, more than speed.

Move on when: one break or none per piece.

5. See-through

Thin enough that the blade shows through the sheet as it comes off. This is the standard for ken. Slow down; most cooks speed up as they get confident and the sheet thickens.

6. Cucumber

Cucumber is softer and has a wet seed core. Cut it to the same length as your daikon pieces, peel around until you reach the seeds, then stop. Practise at 2 mm, the thickness used for kappa sticks.

7. Ken from your own sheets

Stack sheets of the same length and slice them into threads as fine as you can. Uneven sheets show up immediately as uneven threads, which makes this the most honest test of the sheets you have been cutting.

Stacked sheets cut into threads. Even sheets give even threads.

Read your sheet

Every fault leaves a mark on the sheet. Lay it flat or hold it to the light and compare.

Sheet profiles: even; getting thicker along the length; thicker at one end of the width; ridged like a washboard; torn and holed. Evenwhat you want Gets thicker along the lengthedge drifting in One end of the width thickerblade not parallel to the piece across the width Washboardstrokes uneven Holes and tearstoo thin too soon, or a soft daikon
Sheet edges seen side-on, thickness exaggerated. The third row also shows the cause: the blade (grey) tilted away from upright, against the piece.
What happensUsual causeFix
Sheet tears acrossDull edge, or the knife is being pushed into the daikon instead of strokingSharpen; keep the strokes long and even and let the left thumb do the turning
Sheet gets thicker and thickerThe edge is drifting deeper into the vegetableKeep the right thumb on the sheet as a depth gauge; reset after every turn
One end thicker than the otherBlade is not parallel to the length of the pieceUse a shorter piece until it is; check the angle in a mirror
Sheet breaks at the same spot each turnThe piece is not round: a ridge or flat spotTrim the cylinder round before starting
Holes in the sheetToo thin for your current control, or a soft daikonGo back up to the last thickness that worked; buy a firmer daikon
Ridged, washboard surfaceStrokes of uneven length or speedLong strokes of the same length, at a steady pace

Keep a log

Write down, per session: drill number, piece length, number of breaks, and whether the sheet passed the light test. Progress is slow enough that without notes it feels like none. Photographing a sheet held against a window every week makes the change easy to see.

DateDrillPieceTargetBreaksLight test
Mon15 cm2 mm3n/a
Tue15 cm2 mm1n/a
Wed210 cm2 mm4n/a

An example of what a first week can look like. Copy the columns into a notebook.

Using the practice sheets

Questions

How long until I can do katsuramuki properly?

With daily practice most cooks get unbroken 2 mm sheets within a couple of weeks. Even, see-through sheets from a whole piece usually take a few months.

Should I practise on daikon or cucumber first?

Daikon. It is firmer, rounder and has no seed core, so it forgives more. Move to cucumber once you can cut an unbroken 2 mm daikon sheet.

Left-handed: what changes?

Everything is mirrored: the daikon is in the right hand and the knife in the left. With a single-bevel usuba you need a left-handed knife, because the bevel is on the other side.

Is there a shortcut?

For the skill itself, no. For service, when what you need is many cucumber or daikon sheets at a fixed thickness, there are thickness guides that attach to the blade. See knives and tools.